发动机尾气余热驱动的吸附式空调系统仿真与测试

针对在高太阳辐射地区，柴油车驾驶室内使用车载空调会增加车辆发动机的耗油量、降低柴油车经济效益的问题，搭建了一套由发动机尾气余热驱动的吸附式车载空调系统。系统由填充有氯化钙/氯化锰/硫化膨胀石墨复合吸附剂的吸附床、蒸发器、冷凝器、储液罐和阀门组成，使用氨作为制冷剂，利用车辆在行驶时接触到的自然风为吸附床冷却，在发动机尾气余热的驱动下，为驾驶室内提供连续的制冷效果。结合仿真和实验测试，对所设计系统的制冷性能进行了分析，仿真结果表明，系统最优循环时间为45 min，系统的理论平均制冷功率可达3.5 kW以上，系统COP处于0.2~0.25之间。实验结果表明，在230℃的尾气温度条件下，系统能产生3 kW的平均制冷量。在40℃环境温度条件下，系统在蒸发器进出口处的平均温差为6.5℃，平均制冷量为3.2 kW。     

CO2驱沥青质沉积对致密储层的伤害机理——以鄂尔多斯盆地延长组长8储层为例

为了揭示CO2驱替过程中沥青质沉积对致密储层的伤害机理,文中基于岩心核磁共振T2谱测试原理,开展了CO2注入压力下的岩心驱替实验,研究了沥青质在岩心中的沉积特征,评价了沥青质沉积对储层的伤害程度。实验结果表明:沥青质沉积量和渗透率伤害率随着CO2注入压力的升高呈现先快速上升后趋于平缓的趋势;在CO2注入过程中,沥青质主要沉积在弛豫时间大于10 ms的大、中孔隙,导致大、中孔隙占比下降,微细、小孔隙占比增加,且随着CO2注入压力的升高,大、中孔隙占比下降幅度增大,微细、小孔隙占比上升幅度增大;此外,沥青质沉积会引起润湿性发生反转,随着沥青质沉积量的增加,润湿反转指数增大,岩心润湿性不断向强油湿方向转变。     

冷轧预变形对新型铝锂合金的时效析出与力学性能影响

采用大气熔炼铸造及热变形方法制备了Al-4.5Cu-1Li-0.7Mg-1Zn-0.3Ag-0.3Mn-0.2Zr新型铝锂合金板材。通过维氏硬度、拉伸性能、扫描电镜、透射电镜等方法，研究了固溶后不同冷轧预变形量对显微组织和力学性能影响。结果表明，时效前的冷轧预变形量有效促进了新型铝锂基体合金中T1(Al2CuLi)相的析出与均匀分布，减少了θ′(Al2Cu)相的体积分数。冷轧预变形量的增加，缩短了峰时效时间，晶界析出相由连续析出变为非连续析出，无沉淀析出区宽度变小。当冷轧预变形量为15%时，时效态合金的屈服强度与抗拉强度分别达到了668 MPa、690 MPa，延伸率保持在7.9%。     

Preparation of molecularly imprinted fluorescence sensor based on carbon quantum dots via precipitation polymerization for fluorescence detection of tetracycline

A facile and effective method was proposed to prepare the molecularly imprinted fluorescence sensor with carbon quantum dots, which were modified vinyl groups by acrylic acid on the surface. The obtained fluorescence composite material was investigated by transmission electron microscope and Fourier transform infrared spectra. After the experimental conditions were optimized, a linear range of 1.0–60 μmol L⁻¹ was obtained and the detection limit was 0.17 μmol L⁻¹. The novel fluorescence sensor can be successfully used to detect tetracycline in real samples. This study provides a convenient strategy for selective recognition and rapid detection of tetracycline in the complex environment.     

镍基高温合金锥筒形件拉深旋压成形机理研究

针对镍基高温合金因加工硬化严重成形时极易产生破裂和起皱等典型缺陷的问题,以锥筒形壳体类零件为对象,提出了一种由锥形预制坯经过真空固溶处理后拉深旋压成形锥筒形件的方法,并对其成形机理进行了研究。基于Abaqus/Explicit平台,建立了锥筒形件拉深旋压有限元模型,分析了成形过程中的瞬态等效应力、等效塑性应变、切向应力、壁厚及三向应变分布规律。结果表明:在旋压成形过程中,最大瞬态等效应力位于旋轮接触区及附近区域、最大瞬态等效塑性应变位于坯料口部;瞬态切向压应力最大值位于旋轮接触区,而瞬态切向拉应力最大值位于旋轮接触区附近的两侧区域。筒形段中部壁厚减薄,而坯料口部壁厚增厚。旋压成形试验表明,锥形预制坯经拉深旋压后可获得壁厚均匀的锥筒形件。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Predicting visual similarity between colour palettes

This work is concerned with the prediction of visual colour difference between pairs of palettes. In this study, the palettes contained five colours arranged in a horizontal row. A total of 95 pairs of palettes were rated for visual difference by 20 participants. The colour difference between the palettes was predicted using two algorithms, each based on one of six colour-difference formulae. The best performance (r² = 0.86 and STRESS = 16.9) was obtained using the minimum colour-difference algorithm (MICDM) using the CIEDE2000 equation with a lightness weighing of 2. There was some evidence that the order (or arrangement) of the colours in the palettes was a factor affecting the visual colour differences although the MICDM algorithm does not take order into account. Application of this algorithm is intended for digital design workflows where colour palettes are generated automatically using machine learning and for comparing palettes obtained from psychophysical studies to explore, for example, the effect of culture, age, or gender on colour associations.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.